|
 |
FIOA-0402-U
Field Analog Input /Outputs
|
| Características |
| Low cost compact Analog I/O modules with DIN rail mounting |
| Programmable inputs allow same modules to accept RTD, Thermocouple, mA, mV and Volts |
| 12 bit resolution |
| 4 universal analog inputs and 2 analog outputs |
| High Speed Modbus RTU (Slave) communication |
| User definable Address, Baud rate and Parity through Software Configuration |
| 2 wire RS485 port provided on pluggable terminal block |
| Can be multi dropped as Modbus Slave on RS485 Network |
| Indication for Diagnostics, Power and Communication |
| Programming through standard Prizm software .........FREE!! |
| CE marked with optional UL certification |
| Especificaciones |
For mVolt inputs :
Uses 0-100 mV input range resolved in 12 bits.
Total error : ± 0.2% of scale ±1 bit.
For Current inputs :
Uses 0-20mA input range with 4.7W precision shunt resolved in 12 bits.
Total error : ± 0.2% of scale ±1 bit.
For Volt inputs :
Uses 0-10V input range resolved in 12 bits.
Total error : ± 0.2% of scale ± 1 bit.
For RTD input :
Uses 3 wire compensation technique. Excitation Current is 0.5mA.
Power dissipated in RTD is 0.025mW @ 100 W.
Range supported : -200 to 850oC.
For Thermocouple Input :
Uses 0-100mV input range resolved into 12 bits.
Cold junction error is 1o maximum and 0.5o typical.
Total error : 0.5% of scale ± 1 bit + CJC error
Response Time : Worst case 25mSec approx.
Temperatura Drift
(for Digital Count) : 60 PPM
Normalization Factor : 0-99 (Software configurable) |
| Input Type |
Temperatura Range |
1 bit Corresponds to |
| J |
-50 to 1200º C |
0.43º C |
| K |
-50 to 1373º C |
0.61º C |
| E |
-50 to 1000º C |
0.32º C |
| R |
-50 to 1769º C |
2.04º C |
| S |
-50 to 1769º C |
2.31º C |
| B |
0 to 1820º C |
3.21º C |
| N |
-50 to 1300º C |
0.7º C |
| T |
-50 to 400º C |
0.47º C |
| Analog Outputs |
| Resolution |
12 Bit |
Load:
4-20 mA
0-10 V DC |
Less than 500 W
Minimum 1K W |
|
|
| General Especificaciones |
| Power |
+ 24V DC ± 10%, 4W maximum |
| Operating Temp. |
0º to 50º C |
| Storage Temp. |
-20º to 80º C |
| Humidity |
10% to 90% (Non Condensing) |
| Mounting |
DIN rail or back panel mounting |
| Dimensions |
100 W x 70 H x 35 D mm |
| Immunity to ESD |
as per IEC61000-4-2 |
| Immunity to Fast Transients |
as per IEC61000-4-4 |
| Immunity to Radiated electromagnetic field |
as per IEC61000-4-3 |
| Immunity to Conducted disturbances |
as per IEC61000-4-6 |
| Surge |
as per IEC61000-4-5 |
| Radiated emission |
as per EN61000-6-4 |
Communication Port
|
2 wire RS485, RS232,CMOS logic
Signals are available on RJ45 comm
port.
Same two wire RS485 signals are
provided on terminal block |
| Driver |
Modbus RTU Slave |
Baud rate
|
9600, 19.2k, 57.6k or 115.2k
(software configurable) |
| Parity |
Odd, Even or None (software configurable) |
| Device ID |
1-255 (Software configurable) |
|
| Typical Wiring Diagram :- Analog Inputs |
1. Current Input Connections:
 |
2. Voltage Input Connections:
 |
3. RTD Input Connections:
 |
4. Thermocouple Input Connections:
 |
| Typical Wiring Diagram :- Analog Outputs |
1. Current Output Connections:
 |
2. Voltage Output Connections:
 |
|
|
|
|
|
|
